TC668A-Y Calibration: Modules, Cycles and Records

A TC668A-Y calibration bench is bought to remove a person from the loop, not to make the loop faster. The bench comes in 70 MPa and 100 MPa versions; what decides whether it earns its space is how the module is matched to the job and how the cycle is set. Most of this TC668A-Y calibration guide is about those two decisions.

TC668A-Y calibration bench with hydraulic pressure module and touchscreen control panel

What This TC668A-Y Calibration Guide Covers

This TC668A-Y calibration guide follows the work in the order it happens: matching the module to the instrument list, setting a cycle that is honest about settling time, proving the fixture before loading it, and keeping records that can be reproduced.

Matching modules to the job

Use the module whose span sits just above the instrument’s. A 100 MPa module checking a 6 MPa gauge wastes most of its resolution and its accuracy class; a 10 MPa module doing the same job is both faster to settle and more honest about the reading.

When a batch mixes ranges, group by module rather than by instrument type. Changing a module costs more time than batching the work does.

The bench uses replaceable digital pressure modules, so the standard is configured by the module rather than by buying a second bench — and two M20 × 1.5 ports on the front panel let the reference and the instrument under test connect at the same time.

Setting a cycle

The bench closes two loops — pressure, and the mechanical load the circuit sees. Pressure feedback alone reacts after the fact; monitoring the rate of pressure change as well lets the controller ease off before the set point instead of arriving and correcting. That is why it can hold a point while seals and hoses are still taking up strain.

Points are usually 0, 25, 50, 75 and 100 percent of span, and the cycle runs up and down — which is how hysteresis gets measured rather than described.

The bench walks the sequence itself, so a full up-and-down cycle happens without anyone touching a valve. What is left for the operator is deciding what counts as settled: give each point a settling window long enough to stop moving, and use the same window for every point so the record stays comparable. A TC668A-Y calibration is only as repeatable as the settling window behind it.

Fixtures and throughput

Prove the fixture before loading it. A manifold with several stations has several chances to leak, and a leak found after the cycle has run is a cycle wasted. Pressurise the empty fixture, hold it, watch — then load.

Recording what matters

Pressure generation, stabilisation, measurement, error calculation and storage all run inside the cycle, and the pressure curve stays available afterwards for anyone who wants to see how a point behaved rather than only what it read. Where certificate generation is part of the workflow, the PC software takes the stored records and produces the document.

What makes the record reproducible is the header: module used, the standard’s calibration due date, ambient temperature, fixture identification, operator. Batch records without a module identifier cannot be reproduced.

Safety limits

Overpressure protection, sensor fault detection and protection against incorrect connections are part of the control system rather than add-ons. An overpressure alarm can be configured at approximately 120% of the applicable range — set it, and treat it as the last line rather than the working limit.

When it will not hold a point

  • Point overshoots and comes back — settling window too short for the fixture volume.
  • Pressure falls between points — fixture or fitting leak, not the controller.
  • Instruments on the same manifold disagree — check each station separately; one leaking station changes the behaviour of the whole manifold.
  • Repeatability worse than usual on one module only — that module, not the bench.

Daily check and maintenance

Start the day with a single-point check against a stable instrument. It is a check, not a calibration: it tells you the bench is behaving, and it catches a leak before a batch does. Change the oil on the interval your quality system sets, and keep the module connectors clean — a dirty connector reads as drift.

Full specifications are on the TC668A-Y automatic pressure calibration bench product page. For gas and vacuum work, compare the TC668A-Q automatic calibration bench; for a manual hydraulic source, see the TC168T 0–60 MPa hydraulic power source. Hoses, adapters and quick connectors are listed under pressure accessories.

For a TC668A-Y calibration on a specific instrument list, send us the ranges and the media — we will tell you which module covers them and how long a cycle should take.